No products in the cart.
Progress Menu
x
Home / Womens / Home and Decor
This pattern is copyrighted 2021 to Rebecca Page by rebecca-page.com
Please feel free to make garments from this pattern to sell. If you do, we would love you to include a credit to rebecca-page.com as the pattern designer, but it is up to you.
The finished product may only be sold by crafters. It may not be mass produced. You can only sell the finished product; you cannot sell the pattern or these instructions.
Best of luck and happy sewing!
30
Women's Vintage Apron
Member Rating
Difficulty Level
Beginner
Equipment Needed
Description
Add a dash of vintage charm and a vintage vibe to your kitchen with this beautiful vintage apron! No complicated fasteners, buttons, or zippers make this apron a true beginner level pattern!
Not a member yet? Click here to sign up
- +Preparation
- Height adjustment – The pattern is drafted for a height of 5 foot 6 inches. If you are taller or shorter, adjust the length by adding or removing height from the center of the bodice piece, and at the hem of each frill.
- Bust adjustment – As the bodice is designed to just lay against the bust, rather than shape around the bust, it should suit most bust shapes and sizes. A full or small bust adjustment is unlikely to be necessary but if you are aware this style may need one for your shape, we would recommend a making a muslin to check.
- If you get stuck with fitting, see our favorite resources on our Pinterest Sewing Fitting Advice board.
- You can use nearly any woven fabric for both the apron and the lining. If you wish to have the ruffles stick out a little while wearing it, we recommend woven fabric with some structure (e.g. that sticks out vs draping softly) such as cotton, quilting cotton, linen, or taffeta.
- You can use a narrower fabric (e.g. 45 inch / 112cm wide), but some pattern piecing might be required depending on size. To do this, cut the frill 3 piece (the largest frill) with either a seam down the center front, or part-way around the frill. Remember to add the seam allowance to where you are cutting, then join with either a French seam or stitch and serge. The fabric requirements below have been worked out on joining the frill in this way.
- OPTIONAL – You can hem the frills and lining with bias tape if you wish. To do this, you will need approximately 4-5 yards depending on size.
- Thread to match
- Bodice (fabric cut x2)
- Waistband (fabric cut x3)
- Neck Ties (fabric cut 2)
- Frill 1 (fabric cut x1 on the fold)
- Frill 2 (fabric cut x1 on the fold)
- Frill 3 (fabric cut x1 on the fold)
- If you are using 45 inch / 112cm wide fabric, you will need to cut frill 3 in two pieces as above and join.
- Top Lining (lining cut x1 on the fold)
Project OverviewVintage Apron
Difficulty Level = Beginner
Add a dash of charm and a vintage vibe to your kitchen with this beautiful vintage apron! With a halter tie top, classic shapes, and beautiful tiered ruffles, you can bring a feminine touch to your cooking and baking experience. No complicated fasteners, buttons, or zippers make this apron a true beginner level pattern!
Make a few for yourself or as gifts for all the lovely women in your life! So easy to personalize with their favorite colors or fabrics. This apron is also a great palate to show off your unique style and is a fantastic place to showcase your favorite vinyl cut files. Who doesn’t want to feel beautiful in all rooms of their house?
Our Facebook group is a great place to get help, share your tips and creations! We are a friendly bunch, and we love to help and see what you have made.
Please read the full instructions before getting started.
Wash, dry, and press your fabric before starting your project. A bit of prep now prevents shrinking and means your garment will stay the same size you made it.
Never leave a child or baby unattended or allow to sleep in a garment made from one of our patterns with ties, snaps, buttons, or anything they could remove, choke on, or get caught on. Always use caution if you are unsure. We love our patterns, but we love your bundles of joy more!
SizingSize Range
Womens XXS-5XL
Size Chart
This pattern is drafted to the sizes listed below. If you are between sizes, choose the larger size and adjust the pattern to remove the extra width to achieve the intended fit.
Chest
Waist
Hips
Inches
CM
Inches
CM
Inches
CM
XXS
31.0
79.0
25.0
63.5
34.0
86.0
XS
33.0
84.0
27.0
68.5
36.0
91.5
S
35.0
89.0
28.0
71.0
38.0
96.5
M
37.0
94.0
30.0
76.0
40.0
101.5
L
39.0
99.0
32.0
81.0
42.0
106.5
XL
42.0
106.5
35.0
89.0
45.0
114.0
XXL
45.0
114.0
38.0
96.5
48.0
122.0
3XL
48.0
122.0
42.0
106.5
51.0
129.5
4XL
51.0
129.5
46.0
117.0
54.0
137.0
5XL
54.0
137.0
50.0
127.0
57.0
145.0
Finished Measurements (Inches)
Chest
Skirt
Ties
Width at top
Length top to waist
Length from waist to hem
Neck tie length (each)
XXS
7.3
8.8
17.2
33.0
XS
7.8
9.1
18.1
33.5
S
8.0
9.4
18.9
34.0
M
8.5
9.7
19.9
34.5
L
9.0
10.0
20.8
35.0
XL
9.8
10.3
21.8
35.5
XXL
10.5
10.6
22.7
36.0
3XL
11.5
10.9
23.9
36.5
4XL
12.5
11.2
25.1
37.0
5XL
13.5
11.5
26.2
37.5
Fitting NotesMaterials and ToolsWe recommend a 60 inch / 150cm wide woven fabric.
Fabric Requirements 45 inches/115 cm wide (in YARDS)
All one fabric
All separate fabric
Bodice
Lining
Ties
Frill 1
Frill 2
Frill 3
XXS – S
2.50
0.50
0.50
0.75
0.75
1.00
1.00
M – XXL
3.00
0.50
0.50
0.75
0.75
1.00
1.25
3XL- 5XL
5.00
0.50
0.50
0.75
1.00
1.00
2.50
Fabric Requirements 60 inches/150 cm wide (in YARDS)
All one fabric
All separate fabric
Bodice
Lining
Ties
Frill 1
Frill 2
Frill 3
XXS – S
2.50
0.50
0.50
0.50
0.75
1.00
1.00
M – XXL
3.00
0.50
0.50
0.75
0.75
1.00
1.25
3XL- 5XL
3.50
0.50
0.50
0.75
1.00
1.00
1.25
NOTE – If you are using some of the same fabrics for your bodice and any frills, you will need less than listed.
* If you are using a narrower fabric, a directional print, or a fabric with nap you may need more.
** Make sure to wash, dry, and press all fabrics before cutting out in case they shrink.You will also need:
Tools needed are a sewing machine, scissors, pins, tailors chalk, and a tape measure. A serger or overlocker is optional but not required.
Printing Your PatternSettings
The pattern is a separate download. Choose either the US letter paper, A4 paper, or A0 paper size based on the printer you wish to use. If you are in the US or Canada then your printer will likely use US letter paper. Other regions normally use A4 paper. Some people prefer to print their patterns at a print shop: A0 is best in this case.
Print at 100%.
On the second page, you will find a 1-inch and a 3-inch square test box. Print this page first, on its own, and measure these squares.
Once you are happy that the test box is accurate, print the rest of the pattern pages.
Please follow this video for information and assistance on assembling this pattern.
Also, please note that some Rebecca Page patterns and projects also come with cut files and a printable design page which you can use to plan your project if you wish. These are provided in a separate section below to avoid any confusion!
Cutting InstructionsCut each of the pieces according to the directions on the pattern piece. Seam allowances are all included so just cut them as is.
If you are using 45inch wide fabric and need to cut frill 3 in two pieces as per the fabric requirements section on the previous page, join this using either a french seam or serger now before continuing to the sewing section.
Cutting Charts – All pattern pieces are included, however, if you prefer to cut using a cutting chart, the dimensions for the rectangular pieces (in INCHES) are below:
Neck Tie (cut 2) Waistband
(cut 3)Width
Length
XXS
4.0
22.5
XS
4.0
23.5
S
4.0
24.0
M
4.0
25.0
L
4.0
26.0
XL
4.0
27.5
XXL
4.0
29.5
3XL
4.0
31.5
4XL
4.0
33.0
5XL
4.0
35.5
Cutting Checklist:
NOTE – To cut fabric on the fold, fold your fabric over parallel to the selvage edges. Align the pattern piece so it is on the fold of the fabric. Cut around the edges, leaving the fold. If you have folded your fabric correctly the fold will be parallel to the two edges of the fabric that are finished. The raw edges (e.g. the ones you could pick at and threads would come off) will be at a right angle to your fold.
- + Instructions
- PATTERN MARKINGS – Transfer the markings for the Ties from the top of the Bodice pattern piece to one of the bodice pieces.
- HEM – Hem the short edges and the bottom long edge of Frill 1 by turning them to the wrong side ¼ inch twice and press. Topstitch close to the folded edge. Repeat for the other Frill pieces and the short edges of the lining piece. Alternatively, you can finish these edges using bias tape, with a serger, roll hem, or any other hemming method you prefer.
- ATTACH FRILLS 2 AND 3 TO THE LINING – With the right sides up, place Frill 2 on top of Frill 3. Match up the top edges and pin together and then baste in place. With the right sides together, pin the bottom edge of the lining piece to the top edge of the Frills. Stitch using a ½ inch seam allowance. Press the seam up toward the lining. Finish the seam by using a zig zag stitch, serging or using bias tape.
- NECK TIES – With the right sides together, fold the Tie in half along the long edge and one short edge. Pin and then stitch using a ½ inch seam allowance. Leave one of the short edges open for turning. Clip the corners and the turn the Tie right side out. Optionally topstitch. Repeat for the other Tie.
- BODICE – Place one of your Bodice pieces right side up and then put the Ties on top at the markings. Then place the other Bodice piece right side down. Your Ties will now be sandwiched in between the Bodice pieces. Pin along the side, across the top edge, and then down the other side. Stitch using a ½ inch seam allowance. Optionally, topstitch.
- WAISTBAND – Sew three Waistband pieces right sides together along short edges to create on long Waistband. With the right sides together, place the Bodice on the Waistband, matching the midpoints of each. Pin and stitch together using a ½ inch seam allowance. With the right sides up, place Frill 1 on top of the lining and pin together along the top edge. Baste in place. With the right sides together, pin the bottom edge of the Waistband onto Frill 1, matching up the endpoints of each. Continue pinning the Waistband along the top edge of Frill 1. Stitch using a ½ inch seam allowance. Press each of the short ends of the Waistband ½ inch toward the wrong side. Then press both long edges of the Waistband ½ inch toward the wrong side. Fold the Waistband in half, matching the folded long edge together. Pin along the length of the Waistband and then topstitch all around the edge of the Waistband.
Quick Glance Cheat Sheet½ inch seam allowance included – Top stitching ⅛ inch – Basting ¼ inch
Preparation –
Sewing –
0 . PreparationSeam Allowance
½ inch seam allowance included – Top stitching ⅛ inch – Basting ¼ inch
0.1Transfer the markings for the Ties from the top of the Bodice pattern piece to one of the Bodice pieces (the one that you will have facing out as the front, the other one will become the lining).
1 . Hems1.0We will first be finishing the short edges and bottom edges of all three Frill pieces and the short edges of the lining piece.
You can use any method you like to do this. Serging, roll hemming, turning under or using bias tape are all below. However, if you have another method you prefer (such as using ribbon or any other trim!), do this now, then skip to step 2.
SERGER OPTION – Serge the short and bottom edges of all three pieces Frill to finish (do not remove any length). Repeat for the short edges of the lining. For all edges, turn under ½ inch and topstitch in place. Skip to step 2.
ROLL HEM OPTION – Use your serger or sewing machine to do a rolled hem using a ½ inch seam allowance on the short and bottom edges of all three Frill pieces and the short edges of the lining. Alternatively, if your rolled hem foot uses a smaller seam allowance you can either trim the seam slightly first or leave it and have the finished apron be slightly longer. Skip to step 2.
SEWING MACHINE OPTION – You will be finishing the short edges and bottom edges of all three Frill pieces and the short edges of the lining piece. This can be done by turning under, or by finishing the edge with bias tape. To hem by turning the fabric under start at step 1.1, to use bias tape skip to step 1.4.
1.1TURN UNDER OPTION – Turn the hem of the Frill 1 piece under ¼ inch and press.
1.2Turn the hem under another ¼ inch and press. The raw edges will now be enclosed in the folds.
Then, topstitch in place by stitching close to the folded edge.
TIP – You want your stitching to be the same distance from the bottom of the skirt as much as possible so that it looks nice and neat from the outside. To do this, use your presser foot or a marking on your foot plate on your sewing machine to line up your fabric so you get a nice even stitch all the way around.
1.3Repeat steps 1.1 and 1.2 for each of the Frill pieces.
Repeat again to finish both short edges on the lining. Do not finish the bottom edge of the lining, this will attach to the Frills later.
Skip to step 2.
1.4BIAS TAPE OPTION – Open out the fold on one side of your bias tape and press one short side under ¼ inch and press.
1.5On the wrong side of Frill 1, align the fold on the right side of your bias tape with the raw edge and pin in place.
Trim the excess bias tape.
1.6Stitch in place by stitching along the fold on the bias tape.
1.7Fold the bias around to the right side of the Frill and pin to enclose all edges.
1.8Edge stitch along the bias tape close to the edge to secure.
Repeat steps 1.4 to 1.8 to attach bias tape to each of the Frill pieces and the lining.
2 . Attach Frills 2 and 3 to the Lining2.1With the right sides up, place Frill 2 on top of Frill 3. Match up the top edges and pin together and then baste in place using a ¼ inch seam allowance.
This should hide the basting stitches in the seam allowance of the finished garment, but if they are visible at the end, we will remove them.
Treat Frill 2 and 3 as one piece from now on.
Do not attach Frill 1 yet. We will attach this later directly to the Waistband.
NOTE – A basting stitch is a long, loose stitch that is used to temporarily tack the pieces together. If you haven’t used one before, check if your machine has a basting (or it may be called ’gathering’) stitch. If not, lengthen your stitch on your sewing machine so it is as long as possible. Test on a scrap of fabric. Then stitch without backstitching or securing the ends, leaving a tail of threads approximately 3 to 4 inches at either end of your seam. We will pull the bobbin thread later to remove it if it is visible in the finished garment.
2.2With the right sides together, pin the bottom edge of the lining piece to the top edge of the Frills.
2.3Stitch using a ½ inch seam allowance. Press the seam allowance up toward the lining.
2.4You will need to finish this seam. You can do this with either a zig zag stitch or by serging the seam.
Alternatively, for a really neat edge that doesn’t require a serger, you can bind using bias tape following steps 1.4 to 1.8.
3 . Ties3.1With the right sides together, fold the Tie in half along the long edge and one short edge.
Pin and then stitch using a ½ inch seam allowance. Leave one of the short edges open for turning.
3.2Clip the corners and then turn the Tie right side out.
OPTIONAL – Top stitch close approximately ⅛ inch from the edge along both long sides and the enclosed short side to finish.
Repeat steps 3.1 and 3.2 for the second Tie.
4 . Bodice4.1Place one of your Bodice pieces right side up and then put the Ties on top at the markings. They should be centered over the markings.
Then place the other Bodice piece right side down. Your Ties will now be sandwiched in between the Bodice pieces and will trail out the open end of the Bodice.
Pin along the side across the top edge and then down the other side.
Stitch using a ½ inch seam allowance.
NOTE – Make sure to keep the rest of the Ties out of the way, so that they don’t get caught in the seams.
Clip corners and trim seams.
4.2Turn the Bodice right side out and press.
4.3Optionally, topstitch around the sides and top of the Bodice using a ⅛ inch seam allowance.
5 . Waistband5.1Take two of your Waistband pieces, right sides together and pin along one short end.
Stitch using a ½ inch seam allowance.
Repeat to attach the third Waistband piece, creating one long Waistband.
With the right sides together place the Bodice on the Waistband, matching up the midpoints of each.
Pin and stitch together using a ½ inch seam allowance.
5.2With the right sides up, place Frill 1 on top of the lining and pin together along the top edge.
Baste in place using a ¼ inch seam allowance and treat this as one piece from now on.
5.3With the right sides together pin the bottom edge of the Waistband onto Frill 1, matching up the midpoints of each. Continue pinning the Waistband along the top edge of Frill 1.
Stitch using a ½ inch seam allowance.
5.4Press each of the short ends of the Waistband ½ inch toward the wrong side.
Then, press both long edges of the Waistband ½ inch toward the wrong side.
5.5Fold the Bodice backwards down so it is laying flat against the wrong side of the skirt. Keep it folded down here out of the way during this step.
Fold the Waistband in half, matching the folded long edges together.
Pin along the length of the Waistband. Do not stitch yet.
NOTE – You will be tucking the seam allowance from both the Bodice and the skirt into the Waistband.
5.6Flip the Bodice up. Then topstitch all around the edge of the Waistband using a ⅛ inch seam allowance.
This will enclose the raw edges and finish the Waistband.
NOTE – You are stitching the upper, folded edge of the Waistband to the Bodice in this step.
- + Finishing Notes and Congratulations
Finishing Notes and Congratulations
Congratulations, your Vintage Apron is done. Enjoy!
We would love to hear how you got on and see photos of your finished project!
Join us at our Facebook Group, tag us on Instagram, or use the hashtag #rpvintageapron.
Thank you for using a Rebecca Page pattern.
© Copyright 2021
All Rights Reserved
Sales + Licencing InformationProject OverviewVintage Apron
Difficulty Level = Beginner
Add a dash of charm and a vintage vibe to your kitchen with this beautiful vintage apron! With a halter tie top, classic shapes, and beautiful tiered ruffles, you can bring a feminine touch to your cooking and baking experience. No complicated fasteners, buttons, or zippers make this apron a true beginner level pattern!
Make a few for yourself or as gifts for all the lovely women in your life! So easy to personalize with their favorite colors or fabrics. This apron is also a great palate to show off your unique style and is a fantastic place to showcase your favorite vinyl cut files. Who doesn’t want to feel beautiful in all rooms of their house?
SizingSize Range
Womens XXS-5XL
Size Chart
This pattern is drafted to the sizes listed below. If you are between sizes, choose the larger size and adjust the pattern to remove the extra width to achieve the intended fit.
Chest
Waist
Hips
Inches
CM
Inches
CM
Inches
CM
XXS
31.0
79.0
25.0
63.5
34.0
86.0
XS
33.0
84.0
27.0
68.5
36.0
91.5
S
35.0
89.0
28.0
71.0
38.0
96.5
M
37.0
94.0
30.0
76.0
40.0
101.5
L
39.0
99.0
32.0
81.0
42.0
106.5
XL
42.0
106.5
35.0
89.0
45.0
114.0
XXL
45.0
114.0
38.0
96.5
48.0
122.0
3XL
48.0
122.0
42.0
106.5
51.0
129.5
4XL
51.0
129.5
46.0
117.0
54.0
137.0
5XL
54.0
137.0
50.0
127.0
57.0
145.0
Finished Measurements (Inches)
Chest
Skirt
Ties
Width at top
Length top to waist
Length from waist to hem
Neck tie length (each)
XXS
7.3
8.8
17.2
33.0
XS
7.8
9.1
18.1
33.5
S
8.0
9.4
18.9
34.0
M
8.5
9.7
19.9
34.5
L
9.0
10.0
20.8
35.0
XL
9.8
10.3
21.8
35.5
XXL
10.5
10.6
22.7
36.0
3XL
11.5
10.9
23.9
36.5
4XL
12.5
11.2
25.1
37.0
5XL
13.5
11.5
26.2
37.5
Materials and ToolsWe recommend a 60 inch / 150cm wide woven fabric.
- You can use nearly any woven fabric for both the apron and the lining. If you wish to have the ruffles stick out a little while wearing it, we recommend woven fabric with some structure (e.g. that sticks out vs draping softly) such as cotton, quilting cotton, linen, or taffeta.
- You can use a narrower fabric (e.g. 45 inch / 112cm wide), but some pattern piecing might be required depending on size. To do this, cut the frill 3 piece (the largest frill) with either a seam down the center front, or part-way around the frill. Remember to add the seam allowance to where you are cutting, then join with either a French seam or stitch and serge. The fabric requirements below have been worked out on joining the frill in this way.
Fabric Requirements 45 inches/115 cm wide (in YARDS)
All one fabric
All separate fabric
Bodice
Lining
Ties
Frill 1
Frill 2
Frill 3
XXS – S
2.50
0.50
0.50
0.75
0.75
1.00
1.00
M – XXL
3.00
0.50
0.50
0.75
0.75
1.00
1.25
3XL- 5XL
5.00
0.50
0.50
0.75
1.00
1.00
2.50
Fabric Requirements 60 inches/150 cm wide (in YARDS)
All one fabric
All separate fabric
Bodice
Lining
Ties
Frill 1
Frill 2
Frill 3
XXS – S
2.50
0.50
0.50
0.50
0.75
1.00
1.00
M – XXL
3.00
0.50
0.50
0.75
0.75
1.00
1.25
3XL- 5XL
3.50
0.50
0.50
0.75
1.00
1.00
1.25
NOTE – If you are using some of the same fabrics for your bodice and any frills, you will need less than listed.
* If you are using a narrower fabric, a directional print, or a fabric with nap you may need more.
** Make sure to wash, dry, and press all fabrics before cutting out in case they shrink.You will also need:
- OPTIONAL – You can hem the frills and lining with bias tape if you wish. To do this, you will need approximately 4-5 yards depending on size.
- Thread to match
Tools needed are a sewing machine, scissors, pins, tailors chalk, and a tape measure. A serger or overlocker is optional but not required.